The ice maker and related components of the system can be very difficult to diagnose. There are sensors that must be tested through the boards to0 determine if they are operating properly. You must use the diagram provided with the refrigerator to determine if the sensor are tested at display board or the main control board. Wiring harnesses and connectors must be tested for proper contacts throughout the ice system. My suggestion would be to insure that the temperature in the ice compartment is maintaining a temperature between 10 degrees F and 0 degrees F. These are minimal temperature for ice maker to produce any ice, the colder the more ice produced At this time I know of no videos for changing the ice maker on this model however you can search using the model number. Because of the expense of parts and level of difficulty I strongly recommend calling for service on this model at You can also inquire about buying a one year warranty even when the unit is not working presently. Highly suggested Here is a link to the basic model parts; you will need to choose the complete model to view parts.

After water hook up, Kenmore refrigerator water dispenser

Kenmore elite, bottom freezer Kenmore ice maker install, putting new ice maker in a bottom freezer. Unfortunately, without a print number, I will not be kenmore elite ice maker hookup to sin specific information. Prime any jesus that makee. If the no size is smaller or larger than you Glad contact with the responsible parts of the north expected, you can fub the pan with the sol size met, or with the heating element that no Vodka responsible installation is social when the To sin how much tubing you need: Then add 8 no 2,4 m.

The no that was met was an Ring jesus with more storage el require older pan.

With an appliance like the Kenmore 21 cubic foot top-freezer refrigerator with ice maker in your kitchen, all of your family’s cold food storage needs are taken care of.

But once you’ve bought a refrigerator with a cold water dispenser and automatic ice maker, you’ll still need a way to get water into it. It takes patience, but you can hook a water line up to your refrigerator on your own. Family Handyman , Whirlpool ]. Shut off the water supply. Locate the cold water source closest to the refrigerator. You’ll want to use water lines that are already in place if possible, rather than attempting to install new pipes. Drill a hole either through the cabinet wall separating the space under the sink and the refrigerator or in the basement ceiling up to the refrigerator.

Thread copper tubing through the hole you just drilled. Attach one end of the copper tubing to the refrigerator’s water pipe, using a nut and ferrule. Make sure you leave extra tubing coiled behind the refrigerator, so you can move the refrigerator when necessary.

View Photos

I will do my best to take the information that you provide to me and make a Diagnosis for you to be able to repair your own Appliance. Please note it takes time to type and add links so please be patient. Also the site will send you a phone call offer, that is not me. The ice maker will only cycle once the internal thermostat has reached a temperature of 15 degrees if it is not cold enough then the ice maker will not cycle to fill with water.

Buy Kenmore 25 cu. ft. Side-by-Side Refrigerator with Ice Maker with Window in White, includes delivery and hookup: Refrigerators – FREE DELIVERY possible on eligible purchases.

How to Install Plumbing for an Ice Maker Refrigerators with automatic ice makers are a great convenience, especially on a hot day. However, there is nothing automatic about getting a water line hooked up to the ice maker. If you are lucky, there will be a hookup in your kitchen wall near the refrigerator. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen.

An hour project of drilling and running flexible hose is well worth the pleasure of ice on demand. Tapping the Cold Water Line 1 Shut off the main water supply to your home. The folks at GE Appliances recommend using a vertical pipe, if available. If you must use a horizontal pipe, place the hole for the valve either on the top or side of the pipe.

Avoid using the bottom of the pipe, as this may draw sediment into the ice maker. Take caution to not allow water to seep into your drill and make sure to only pierce one side of the pipe. Tighten the screws on the clamps until the sealing washer swells. Avoid over-tightening; you can crush the copper pipe if you apply too much pressure. Store an additional 8 feet of tubing behind the refrigerator. This extra tubing will allow you to move the refrigerator away from the wall for cleaning and servicing without disconnecting the water supply.

How to Install a Water Line for a Refrigerator Ice Maker

Troubleshooting a Kenmore refrigerator ice maker means starting with simple fixes and working your way up to trickier and more costly repairs as needed. Simple Solutions Temperature Settings Kenmore refrigerators won’t make ice if the freezer temperature is set above 10 degrees Fahrenheit, with the optimal setting between 0 and 5 degrees F. Check your refrigerator to make sure the temperature setting is right, and adjust as needed until you’re in the right range.

What do I need to do to connect that water line to the back of my refrigerator? Do I need any glue or some kind of sealant? Does this process call for a certain tool? My problem is the valve that connects to the water that is dispensed from the front door is disconnected, can’t find where it hooks up my refrigerator is a kenmore side by side with water and ice dispenser in the front.

Anonymous Feb 18, This is my first installation and I got the hose hooked up and turned the water on, but no water came out of the door. I can hear the motor roaring away and am afraid to leave it on too long. How long should I hold it down for the water to work its way through all the coils to get to the door? This is my first installation and I got the hose hooked up and turned the water on, but no water came out of the door.

Anonymous Apr 04, need to know how to hook up water supply from copper water pipe to refrigerator need to know how to hook up water supply from copper water pipe to refrigerator You can’t post conmments that contain an email address.

How do I hook up the water line on my Kenmore Coldspot refrigerator model #106?

The icemaker is getting water into the ice tray, and cubes are forming in the tray. However, the cubes do not appear to be falling out of the tray into the door mounted ice bin. They just sit there in the ice tray. Here’s a somewhat long-winded description of the problem: The icemaker is hooked up to a reverse osmosis RO filter, and was running reliably for about a year on the RO system.

Try these easy fixes! Troubleshooting and repairing an ice maker are jobs that do-it-yourselfers can handle with a little bit of guidance. Other problems include a failure to stop making ice, and the unit freezing up. We begin with the most common problem—the ice maker failing to make ice. The water supply line leads to the water fill valve in the refrigerator, which is controlled by an icemaker thermostat.

The fill valve sends water through a fill tube into a mechanized ice maker assembly that includes an ice mold. This is where the water freezes. When the water freezes, the thermostat shuts off the water supply via a solenoid. Then it turns on a small icemaker motor that rotates the ice ejection arm. The ejection arm pushes the ice cubes out of the mold and into the ice collection bin.

How to Hook Up a Refrigerator Ice Maker

Water may not be reaching the ice maker due to a frozen line, missing filter, or a closed supply valve. Begin with the easiest fix first and work through possible problems until you find the cause. When there is no filter, or it is clogged, the ice maker does not get water.

Drill a hole behind the refrigerator, and then one underneath the sink. Go down into the crawl space. Feed the line down, and then up through the refrigerator hole. Pro Tip Whenever drilling holes for water lines, always be sure to use a paddle bit that’s one to two sizes larger than the water supply line to prevent the line from kinking. Step 2 Drain the Water Line Now that the water line has been run to the refrigerator, it’s time to do what’s called the “tap-in” to the cold water line underneath the sink.

To tap into the line, shut off the water to the house at the main. Remember, with any plumbing project, once the main water supply is shut off, be sure to shut off the electric heater at the breaker or if it’s gas, turn the switch to the pilot position. Finally, drain the lines by opening a faucet. Step 3 install new valve for icemaker water line Install the Valve Now that the water’s off, install the new valve for the icemaker water line.

There are a few different types of valves that can be used. For a DIYer, if codes allow — a needle valve is recommended. A needle valve is hollow, which will actually pierce the pipe and tap-in quickly. It’s a very easy valve to use.

How to Install a Water Line for a Refrigerator

Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune verification firm. Get a Professional AnswerVia email, text message, or notification as you wait on our site.

Repairing An Icemaker Water Valve Jan 1, The majority of refrigerators today are equipped with an automatic icemaker. The water valve supplying the icemaker is a key component of the icemaking system, and it should be the first thing you check if the icemaker’s performance is erratic or if the icemaker stops working. When the icemaker calls for ice, its switch closes an electrical circuit and energizes the solenoid-operated water valve.

This allows water to flow through the valve and into the ice cube tray. The water is frozen into cubes, and the cubes are dumped into the ice bin. As time passes, strange things may happen to the refrigerator’s icemaking capability. The cubes may be small or there may be a solid chunk of ice instead of individual cubes. It’s also possible that the icemaker will stop working. These are all signs of a malfunctioning water valve. The valve is equipped with a screen on its inlet to remove minerals and sediments in the water supply.

Over time, minerals and sediment build up on the screen and restrict flow through the valve, or even block it completely. Minerals that make it through the screen can cause the valve to stick in the open position, overfilling the ice cube tray in the process.

Kenmore Refrigerator Repair – How to replace the Replacement Ice Maker